• Home
  • Microwave Error Codes

Microwave Error Codes

Smeg microwaves are designed with advanced electronic controls and multiple safety systems to ensure efficient and reliable cooking. When an issue is detected, the appliance may display error codes to prevent damage and help identify the problem quickly.

Below is a refined and slightly more detailed guide to common Smeg microwave error codes, their causes, and solutions.

Microwave Error Codes
Error Code
Causes & Solutions
E01
Door Not Closed / Door Switch Error

Issue:- The microwave will not start because the door is not securely closed.

Possible Causes & Solutions:

  • Door not fully shut – Close the door firmly until you hear a click, ensuring the latch engages completely.
  • Misaligned door hinges – Check if the door sits unevenly and gently realign or adjust if possible.
  • Faulty door switch – If the microwave still doesn't start, the internal door switch may need inspection or replacement.
E02
Overheating Protection

Issue:- The microwave stops operating due to excessive internal temperature.

Possible Causes & Solutions:

  • Continuous usage without breaks – Allow the microwave to cool down for at least 15–20 minutes before using again.
  • Blocked ventilation openings – Ensure air vents are not obstructed by walls, grease, or dust buildup.
  • High ambient temperature – Avoid placing the microwave near heat sources like ovens or direct sunlight.
E03
Temperature Sensor Error

Issue:- The microwave cannot accurately detect or regulate temperature.

Possible Causes & Solutions:

  • Sensor malfunction or disconnection – Restart the appliance after unplugging to reset the system.
  • Food residue near sensor area – Clean the interior thoroughly, especially around sensor zones.
  • Persistent issue – A faulty sensor may require professional servicing or replacement.
E04
Magnetron / Heating Error

Issue:- The microwave is running but not heating food properly.

Possible Causes & Solutions:

  • Magnetron failure – If the appliance runs without heating, the magnetron may need replacement.
  • Power supply fluctuation – Ensure a stable voltage supply to maintain consistent heating performance.
  • Internal component wear – Long-term usage may require servicing of heating-related components.
E05
Turntable / Motor Error

Issue:- The turntable is not rotating properly during operation.

Possible Causes & Solutions:

  • Turntable not seated correctly – Remove and reposition the glass tray securely on the roller ring.
  • Debris in roller ring – Clean any food particles that may block smooth rotation.
  • Faulty motor – If rotation does not resume, the turntable motor may need replacement.
E06
Control Panel / Keypad Error

Issue:- Buttons or displays are unresponsive or behaving irregularly.

Possible Causes & Solutions:

  • Moisture on the control panel – Wipe the panel dry and avoid operating with wet hands.
  • Temporary electronic glitch – Unplug the microwave for a few minutes to reset the system.
  • Worn keypad or control board – Persistent issues may require replacement of the control interface.
E07
Electrical / Power Supply Error

Issue:- The microwave does not power on or shuts off unexpectedly.

Possible Causes & Solutions:

  • Loose plug or damaged cord – Ensure the power cable is intact and securely connected.
  • Faulty power outlet – Test with another appliance or switch to a different outlet.
  • Internal electrical fault – Requires professional inspection for safe resolution.
E08
Cooling Fan Error

Issue:- The internal cooling fan is not operating correctly.

Possible Causes & Solutions:

  • Fan blocked by grease or debris – Clean ventilation areas to restore airflow.
  • Overheating due to fan failure – Stop using the appliance until the issue is resolved.
  • Faulty fan motor – May require replacement if airflow does not improve.
E09
Electronic Control Board Error

Issue:- The microwave displays persistent faults or behaves unpredictably.

Possible Causes & Solutions:

  • Temporary system error – Power off, unplug, and restart after a short wait.
  • Voltage fluctuations – Use a surge protector to stabilize power input.
  • Control board failure – Continuous issues may require professional repair or replacement.
E10
Unusual Noise / Vibration Warning

Issue:- Excessive noise or vibration during operation.

Possible Causes & Solutions:

  • Uneven placement – Ensure the microwave is placed on a flat and stable surface.
  • Loose internal or external components – Check that the turntable and accessories are properly fitted.
  • Worn internal parts – Persistent noise may indicate wear in internal components requiring service.

Troubleshooting Tips

  • Clean Regularly: Remove food splatters and grease buildup from the interior and turntable area to maintain performance.
  • Ensure Proper Door Closure: Always close the door firmly before starting the microwave.
  • Avoid Overheating: Allow cooling time between long cooking cycles.
  • Check Components Periodically: Inspect the turntable, seals, and control panel for wear or damage.
  • Use a stable power supply: Avoid voltage fluctuations to protect internal electronics.
100% Genuine SMEG Parts

100% Genuine SMEG Parts

Completely authentic component.

Fast Shipping

Fast Shipping

Most orders ship out same day

Full Customer Support

Full Customer Support

We are providing 24/7 customer support

Wishlist

Wishlist

You currently have 0 items in your Wishlist

Compare

Shopping cart ( 0 items)

You currently have 0 items in your Cart

Return to shop